Build a cheap turbofan: Difference between revisions

From NPrize
Jump to navigationJump to search
m (https for wikipedia)
(→‎Fixing blades to rotor: price induction and bladon link)
Line 63: Line 63:


===Fixing blades to rotor===
===Fixing blades to rotor===
In real engines, blades are fixed like [http://www.shutterstock.com/pic-9557743/stock-photo-jet-engine.html this], with a dovetail or fir-tree shape that allow them to be mounted and removed axially but not orthogonally. The main problem appearing with this kind of mount is related to the size of the engines we aim. As the diameter of the fan shaft gets smaller, the available space for the blade roots gets smaller, and require a higher precision for their manufacturing. The strength applying to the fixation is luckily reduced due to the small weight of the blades. A simpler design in blade root would be nice for manufacturing ease, a simple square-section root is probably enough.
In real engines, blades are fixed like [http://www.shutterstock.com/pic-9557743/stock-photo-jet-engine.html this], with a dovetail or fir-tree shape that allow them to be mounted and removed axially but not orthogonally. The main problem appearing with this kind of mount is related to the size of the engines we aim. As the diameter of the fan shaft gets smaller, the available space for the blade roots gets smaller, and require a higher precision for their manufacturing. See this example of small fan, from [http://www.price-induction.com/site_media/images/dgen-net/technologies/optimisation_de_masse_grand.jpg Price Induction]. The strength applying to the fixation is luckily reduced due to the small weight of the blades. A simpler design in blade root would be nice for manufacturing ease, a simple square-section root is probably enough.
 
Another lead is to create the blade disk and the blades in a single piece. This can be done with modern manufacturing process like electric discharge machining, 5-dof machining or even laser-based 3D printing. Here is an example from Bladon Jets, [http://www.bladonjets.com/technology/blisk/ the BLISK].


===Fixing blades to stator===
===Fixing blades to stator===

Revision as of 00:14, 1 October 2013

This page gathers general information on turbofans. Our proposed design is scattered in several pages, with an index at the bottom of this page.

How to build a cheap (~ $150) turbofan?

Turbofans are the most efficient engine design for subsonic speeds cruising. They are more powerful and way lighter than reciprocating engines, fly at higher speeds than turbopropellers, and are less fuel-greedy than supersonic-enabled turbojets or other engines. They are however very difficult to design and manufacture and are thus very expensive. On this page, we will explore how costs can be reduced while still having adequate capabilities for high altitude flight.

General principles

Lots of information are available on Wikipedia's page. General principle is that there is a combustion that puts energy into a gas, this energy is extracted by a turbine, and the turbine drives both the fan that provides thrust and the compression stage that feeds the combustion with oxygen. As air is compressed from the intake, more air becomes available for combustion, and thus create more work on the turbine, and more intake, and so on. The fan provides thrust by creating a massive air flow, and the engine's core also creates thrust by evacuating the high-speed hot combustion gas. In commercial turbofan engines, the fan is generally responsible for 90% of the overall thrust.

Some design properties and configurations have to be properly calculated depending on the use of the engine, mainly for the intended aircraft speed:

  • The Bypass ratio (BPR) is a ratio between the mass flow rate of air drawn in by the fan but bypassing the engine core to the mass flow rate passing through the engine core. A BPR = 0 would be a turbojet engine. The higher BPR, the more efficient the engine, but also the slower exhaust speed.
  • The number of spools: modern engines embed a second and sometimes a third concentric shaft for high pressure operations. The low pressure shaft, the innermost, has the fan mounted on it. One stage engines exist and are less complicated and expensive to build, but are much less efficient. Indeed, higher rotation speeds in the internal spools allow to provide a more efficient compression. A gearbox may be needed to drive the fan if the shaft has a too important rotation speed in the case of a single-spooled turbofan, but this is not an easy task due to this very speed. Commercial engines featuring a gearbox for the turbofan's fan are expected to reach market in 2012. Multi-spooled engines prevent this issue, by keeping the low-pressure stages at relatively low speeds, suited for the fan, but are not yet optimal.
  • The compression ratio is the ratio of the pressure of intake air on compressor discharge air. It is closely determined by the number of stages in the compressor and their efficiency. More compression means more air to blend with fuel and to cool the engine, and even more pressure at output, increasing the speed and mass of output gas and thus the work that can be extracted by the turbines and overall engine efficiency.

Turbojet/turbofan engine simulation software from NASA: EngineSim

A must-read book by Klaus Hünecke: Jet engines: fundamentals of theory, design, and operation.

Video documentaries from a turbine renovator in Canada, probably the best resource on the Web for seeing what's inside real engines: on youtube. Thanks AgentJayZ!

Design versus manufacturing

Design configurations and properties taken into concern on real engines tend to increase efficiency, i.e. higher thrusts for lower fuel consumption, but also try to reduce the exhaust noise. Cost is of course a concern, and an efficiency by itself, but maybe not a hard-constraint as it is for us. Safety of operation is their primary concern, whereas cost and ease of maintenance are our primary concerns -- and maintenance will be an important part of the job if the quality goes down with the cost.

Shaped core or shaped shaft?

An obvious but important optimization to reduce cost and complexity of manufacturing is to have a simpler design of the parts creating the gas volume of the engine's core, i.e. the rotor(s) and the stator. In the above schema, we see that the shaft is straight and that the core envelope is curved suit required volume on each stage, although in real life, both are curved. If we take the required volumes on each stage and that we fix the core's envelope shape to a cylinder, the shaft will have a bumped profile (small-large-small diameter). This is much less expensive to design and produce, with a simple lathe (turning). Earlier engines, like the J79, have a cylindrical envelope. A curved envelope is complicated to build, requiring welding, pressing, stage bolting, the same techniques used in stator-construction in modern engines.

Real-world engines don't have a massive turned shaft because of the weight. They consist of plates, for each compressor and turbine stage, that are linked together to the next stage using a cylindrical bolted joint. So basically, the shaft has no core, it's hollow, except for the plates on each stage. Our small engine design allows us to have a more simple design, since having a shaft turned in raw metal won't change much on its final mass. Moreover, we may use a turbine-level mechanism embedded in the stator to try to cool it, which would make it hollow. The main mechanical issues are probably how to properly fix the blades on rotor and stator, how to fix the rotor on the stator with little gap, and how to balance it/them?

Compressor and turbine blades

The most complicated parts to build in a turbofan or turbojet engine are the turbine and compressor blades. The high-pressure turbine specially have to face very high temperature and pressure. On real engines, they are made of nickel-based superalloys or are ceramic-coated. It's the inability of blades to withstand heat and work that limit the power of the engine. Indeed, around 70% of the gas provided by the compressor is used only for chamber and turbine cooling, instead of using it to burn more fuel and create more thrust.

The compressor and the turbine are not only made of blades on the rotor, but also blades on the stator. They prevent a rotating air flow driven by the action of rotor blades to form inside the engine, which would decrease the energy of the gas. Stator blades or vanes redirect the airflow on the next stage in the more efficient direction.

Highest efficiencies are reached in turbofans when gaps are reduced between rotor blades' tip and the stator, as well as between the stator blades' tip and the rotor. As always, good efficiency means high precision and higher cost. Anyway, the precision of blades will have to be very good if we don't want it to dislocate when it reaches the high rotations-per-minute achieved by such engines. The shape of the blade and the parameters of their cascade also affects the efficiency. A small 5 stage supersonic compressor providing the same pressure rise than a 15 stage subsonic compressor is less efficient, but it may be compensated by the higher thrust-to-weight ratio.

Blade geometric design is also very complicated. First turbine engines had flat blades. At the time, the efficiency of the engine was so terrible that it was believed that turbojets would never beat reciprocating engines. Then, in 1926, Alan A. Griffith proved that if blades were designed as airfoils, the engine would behave way better, and would even be efficient enough to deserve being built. Airfoils for blade designs allow compressor stages to better increase the static pressure since they create an expander, an increasing area for the air flow to pass through.

Design considerations

Temperature control

Cooling is always needed in turbines, even if recent advances in materials and coatings increased the ability of blades to withstand heat. Since we will use low cost metals, cooling will be the main issue once we figured out how to build the engine. Expected combustion chamber temperature is around 2000°C for hydrocarbon or alcohol fuels. Iron melting point is around 1500°C so it will be way off-limits, and even below that, it will deform before melting. And should we mention that blade deformation at high-centrifugal loads, caused by the high rpm, is a very good way to blow the engine off?

Several cooling ways are used in a turbofan/turbojet engine: in the combustion chambers, only a small amount of the actual air flow is used for the combustion, around 20%. The rest is injected on the walls of the chamber and in the end of the combustion to dilute the hot gas, and to prevent the walls from melting (film cooling). Then, the first object struck by this hot gas is the vanes the turbine, which are, on actual engines, made of a ceramic-coated high-temperature alloy, but more importantly, hollow. Blades are welded on the stator ring, around which air from the compressor discharge or bleed circulates, enters the blades, and evacuates through small holes in the blades (convective cooling and film cooling). For the rotor blades, the same principle is used, but with compressor air passing inside the rotor.

Startup and ignition

Startup can be done at ground manually, with compressed air or a high speed electric engine for example, which will allow to reduce the weight and complexity of the engine. On the other side, a turbine engine is a nice way of having power on-board, using reducing gears and an alternator. That would also reduce the weight required for batteries, and the alternator would be used reversely as a startup DC motor. Also, the accessories attached to the reduced shaft would allow hydraulic or pneumatic power to be considered.

Igniter mechanisms must be integrated to the engine, possibly a self-maintaining igniter like a thread of tungsten, as used in miniature R/C engines. The combustion should be self-maintaining, but if pump or throttling malfunction, or more generally if a turbulence in the intake happen, leading to a discontinuous flow of fuel or air and compressor stall, re-ignition would have to be made during the flight.

Sensors

Engine must be designed with sensors, at least to determine if the engine is running properly or if it's under failure, and to control its rotation speed to ensure it's running at an efficient enough value, with regard to altitude (pressure and temperature). That can be done with a rotation sensor, measuring the magnetic field disturbances created by the blades or the rotor. Engine temperature should be controlled and recorded too. Pressure at different stages would be very useful for engine development, then for behavior indications when running at high altitude. The rotor speed information and altimeter may be redundant with some of the pressure information.

Fixing blades to rotor

In real engines, blades are fixed like this, with a dovetail or fir-tree shape that allow them to be mounted and removed axially but not orthogonally. The main problem appearing with this kind of mount is related to the size of the engines we aim. As the diameter of the fan shaft gets smaller, the available space for the blade roots gets smaller, and require a higher precision for their manufacturing. See this example of small fan, from Price Induction. The strength applying to the fixation is luckily reduced due to the small weight of the blades. A simpler design in blade root would be nice for manufacturing ease, a simple square-section root is probably enough.

Another lead is to create the blade disk and the blades in a single piece. This can be done with modern manufacturing process like electric discharge machining, 5-dof machining or even laser-based 3D printing. Here is an example from Bladon Jets, the BLISK.

Fixing blades to stator

This is a major issue. On real-size engines, the stator is thick enough to have a rail into which the perpendicular-to-the-blade-roots are inserted and fixed. Creating a perpendicular blade root is already a challenge. Rotor blades would be able to compensate this problem by having longer roots with a locking mechanism on their side, but for the stator, the limited thickness of the stator's wall forbids it. Maybe bolting should be considered. In that case, the screw heads would likely surpass the core's envelope and lightly disturb the fan flow.

External hardware

Fuel tanks in the wings, fuel pumps, fuel lines, and engine mounting will have to be designed too. Electrical wires for pumps, sensors, ignition and possibly the startup motor/alternator will also be required. Sensors will require input ports on the computer, and pump driving (= engine control loop) will require at least one output port for each engine on the computer.

Bearings

Two kinds of bearings are used in turbines.

  • Ball bearing: stator and rotor are joint using a ball bearing constantly bathed in oil to survive to high speeds/temperature.
  • Fluid bearing: pressurized oil prevents parts from touching, due to hydrostatic. Longer life and no maintenance, but harder to build and to operate.

Carbon or composite lip or blade seals prevent the oil from escaping to other parts of the engine. They may be arranged as labyrinth seals to increase their effect. Air bled from the compressor discharge is often used to counteract the oil pressure on the seals.

Our design propositions

From the different concerns expressed above, we propose a design for a low-cost turbofan. We also consider and propose alternative turbofan designs based on a mixed-flow turbine. Several pages have been created in the Turbofan category to explain each subsystem and parts manufacturability:

  • Compressor: A three to five stage compressor, with a design allowing easy manufacturing.
  • Blades: How to design an cheaply manufacture compressor, turbine and fan blades.
  • Combustors: Combustors are the power input of the engine, and need not to melt while sustaining the combustion.
  • Bearings and cooling: high speed rotations require adapted bearings and cooling, which may be reused for rotor and even turbine cooling.

Turbofan design procedure

  1. evaluate required thrust (from aircraft mass and lift, but also flight characteristics)
  2. calculate required mass flow rate for the fan (thust is calculated from MFR and flow speed)
  3. fix bypass ratio and fan diameter and rpm, thus giving core diameter (BPR may be fixed by design)
  4. calculate required power to drive the fan alone
  5. evaluate a gross compressor driving power (refined later)
     
  6. calculate total power that has to be drawn from the turbine (fan + compressor + losses)
  7. calculate mass flow rate for the combustion alone
  8. calculate mass flow rate for cooling chamber and turbine
    1. calculate mass flow rate for cooling chamber
    2. evaluate mass flow rate for cooling turbine to add to the latter
    3. calculate entropy and fluid parameters at combustor discharge (speed, temperature)
    4. calculate temperature of turbine vanes and blade and check if it is acceptable
    5. iterate on item 8.1 until temperature is unacceptable
  9. calculate the number of turbine blades and stages required for this power
  10. calculate compressor discharge pressure and pressure ratio
  11. calculate how many compressor stages are required depending on sonic or supersonic blade design and fix design
  12. calculate compressor driving power
  13. iterate on item 6 until total power varies
  14. design blades for all calculated parameters and re-run at item 6, total power may have changed